 |
| |
| This site requires new users to accept that a small amount of member data is captured and held in an attempt to reduce spammers and to manage users. This site also uses cookies to ensure ease of use. In order to comply with new DPR regulations you are required to agree/disagree with this process. If you do not agree then please email the Admins using info@nikondslr.uk after requesting a new account. Thank you. |
| Moderated by: chrisbet, | ||
| Author | Post | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
Robert
|
This afternoon using the D200 with a Sandisk Exreme III 4Gb card freshly formatted in camera. I took about 15 images then the camera refused to make another exposure, I checked the top screen and where the number of exposures is usually shown it displayed (I think) REC I tried to view the images I had exposed but the message on the screen said 'No images on this card'. As I was photographing one of my Marlin cars, I was not too concerned about the loss of the images so I reformatted the card again. Normality was restored and I continued photographing the car. I did not remove the card or check the seating. I took a further 80 exposures with no issues. The battery was slightly down but at least half of the pictures were taken with the built in flash and the battery indicator still shows about one third remaining. Any ideas? |
|||||||||
Ed Matusik
|
Did you accidentally shut off the camera before the buffer was finished loading the data on the card? I've done that and had the camera lock up on me as well. |
|||||||||
Robert
|
Not impossible Ed, I was clambering over and under the car in quite rugged conditions I could have switched it off accidentally? |
|||||||||
Iain
|
I've had a card fail completely but I've never had one do what you experienced. |
|||||||||
Robert
|
What free software for Mac is there to recover images from the card? I used to have 'Image Rescue' but it wasn't updated a while back for the newer OS's so it's no linger viable. Also it's on a tiny disk which you can only use with tray loading drives which I no longer have. Even though I have reformatted the card the images will probably still be there. |
|||||||||
jk
|
I use one of the following. ImageRescue DiskDrill FileSalvage FileSalvage version 7 does a very good/best job and gets most stuff back. |
|||||||||
Robert
|
Thanks JK, I'm sick of d/ling 'free' software only to find it's free but does nothing unless you pay for it. I only want to recover a dozen or so images, they are there I have seen them but I'm not paying $25 for a few images I don't actually need, I just wanted to extract them to get a clue what went wrong. The last d/l was free but it's a command line interface, not my cuppa! JK would probably be at home with it it runs on Linux too. Attachment: Screen Shot 2012-08-03 at 21.22.29.jpg (Downloaded 39 times) |
|||||||||
Graham Whistler
|
The San Disk free software provided with all their high end CF cards works very well. I had a student on one of my studio workshops who lost all his days work when placing his card in car reader on his laptop. We were able to use the rescue disc and recovered several thousand images from all previous shoots! |
|||||||||
Robert
|
I have it Graham, it has worked well on the rare occasion I have needed it. However it won't run on any Mac I have. I contacted Image rescue because the software won't update with their updaters. I got the probably predictable response that they don't do free updates for free software. In other words the bundled Image Rescue software you get with a Sandisk card is a fully functional free trial with limited life. I recently got a new Sandisk SD 16Gb card but they don't seem to include the recovery disk with SD cards. I don't need a new CF card so it looks like I will have to do without. I keep planning to get Disk Warrior, perhaps this might be another reason if it will recover CF Cards. There is always something else higher up the priorities list. |
|||||||||
Eric
|
Robert wrote:I have it Graham, it has worked well on the rare occasion I have needed it. That's a bit shortsighted of Sandisk not issuing software that works on a Mac? Don't Lexar do a Mac version with their cards? |
|||||||||
Robert
|
Eric wrote:Robert wrote: They do include a Mac version Eric, but because Apple update the OS every couple of years, the software is easily made inoperative due to the upgrades. I suppose I could load an early version of the software on one of my very old Macs but it's hardly worth it. |
|||||||||
Eric
|
Robert wrote:Eric wrote: Now you know why I never chase upgrading  |
|||||||||
Graham Whistler
|
I'm afraid I never got on with Macs. PC work for me but Windows is still far from perfect and now they are talking about version 8 when I'm just getting 7 to behave! |
|||||||||
Eric
|
Graham Whistler wrote:I'm afraid I never got on with Macs. PC work for me but Windows is still far from perfect and now they are talking about version 8 when I'm just getting 7 to behave! Still using XP on my desk computers! Far more stable and intuitive than the later versions. I have windows 7 on my laptop...still struggle with it as an OS. IMHO ...windows 7 is the best reason I have seen to switch to Mac!  |
|||||||||
Graham Whistler
|
I have been doing serious video editing last 3 weeks with a high end PC Windows 7 and Premier CS6 PC it is proving very stable and there is huge amount of high def data on the raid. I shall not be moving to 8 in a hurry. |
|||||||||
Robert
|
Eric wrote:Graham Whistler wrote:  |
|||||||||
jk
|
Graham Whistler wrote:I have been doing serious video editing last 3 weeks with a high end PC Windows 7 and Premier CS6 PC it is proving very stable and there is huge amount of high def data on the raid. If it is broke then dont try to fix it. W8 is more about getting tablet like features and touch screen as eventually the mouse will be replaced. |
|||||||||
Eric
|
Graham Whistler wrote: I have been doing serious video editing last 3 weeks with a high end PC Windows 7 and Premier CS6 PC it is proving very stable and there is huge amount of high def data on the raid. I am sure 7 is very capable of performing functions and running software. For me, the interface is too invasive. It takes over doing things in its way ...that I prefer to do myself in my way....especially 'housekeeping' activities. I lost count of the times I said "why do I have to do it like that?" But then again ...I was weaned on DOS, so I am still very 'manually wired'. Mouse? Havent used one in 15 years! Dont even know if I still have one! |
|||||||||
Current theme is Blue
| A small amount of member data is captured and held in an attempt to reduce spammers and to manage users. This site also uses cookies to ensure ease of use. In order to comply with new DPR regulations you are required to agree/disagree with this process. If you do not agree then please email the Admins using info@nikondsl.uk Thank you. |